Tech Support Guy banner
Status
Not open for further replies.
1 - 10 of 10 Posts

·
Registered
Joined
·
157 Posts
Discussion Starter · #1 ·
After recently upgrading to an FIC MB and AMD k62/550, my computer now hangs on the Win 98 start up screen for what seems like forever (it's probably only a minute or so, but it's about 5 times longer than before I upgraded). It eventually gets beyond this and runs normally.
Any ideas what's going on?
 

·
Registered
Joined
·
45,855 Posts
By startup screen do you mean the logo screen? Try pressing esc to see what is going on beneath it. Do you have an antivirus scan running from autoexec.bat? If you bypass autoexec.bat by using msconfig, does it load any faster?

http://support.microsoft.com/support/kb/articles/q188/8/67.asp

If you do a "logged boot", then run bootlog analyzer and check the "show delays" box, it will show where any delays are occuring (other than "startup" programs):

http://www.vision4.dial.pipex.com/

To do a logged boot you must access the boot menu (ctrl key on startup>boot menu>logged boot)

You save a copy of the text file that shows the delays and post it here.

Does the motherboard use a VIA or ALI chipset -- and have you installed the drivers for it if it does.
 

·
Registered
Joined
·
12,041 Posts
Just posting the contents of the file for easier viewing

21:16:40 2.17 LoadSuccess = C:\WINDOWS\IFSHLP.SYS
21:16:42 0.83 Loading Vxd = VMM
21:16:43 0.00 LoadFailed = ndis2sup.vxd
21:16:43 1.00 LoadSuccess = COMBUFF
21:16:50 0.00 DEVICEINITFAILED = MTRR
21:16:50 0.44 DEVICEINITSUCCESS = VTD
21:16:52 0.33 Dynamic load success s3.vxd
21:16:53 0.33 Dynamic load success mmdevldr.vxd
21:16:54 0.28 DEVICEINIT = IOS
21:16:56 0.94 DEVICEINITSUCCESS = VMOUSE
21:16:57 0.33 DEVICEINIT = NDIS
21:16:59 24.33 Dynamic load success vnbt.386
21:17:24 0.28 Initing hsflop.pdr
21:17:25 1.50 Initing esdi_506.pdr
21:17:26 1.50 Initing esdi_506.pdr
21:17:28 0.33 Init Success esdi_506.pdr
21:17:28 39.94 INITCOMPLETE = CONFIGMG
21:18:08 0.50 INITCOMPLETESUCCESS = CONFIGMG
21:18:09 0.00 INITCOMPLETEFAILED = SDVXD
21:18:10 0.28 Dynamic load success C:\WINDOWS\system\serial.vxd
21:18:11 0.50 Dynamic init success WINMODEM
21:18:11 0.33 Dynamic load success Bt848.vxd

From Microsoft, wondering about the MTRR one, anyone know

InitCompleteFailed = SDVXD
Windows automatically loads a miniature disk cache to increase the speed of the startup process. When the startup process is complete, the miniature disk cache is unloaded from memory. When the cache is unloaded, the "InitCompleteFailed = SDVXD" line is added to the Bootlog.txt file to indicate that the miniature disk cache has been removed from memory. This behavior is typical.

DeviceInitFailed = MTRR
Memory Type Range Registers (MTRR) is a .vxd file that is responsible for manipulating memory ranges. This file is loaded with DirectX 5.0; however, none of the DirectX core components use the service that is provided by MTRR. The Ntkern file and some video adapter drivers do use the service that is provided by MTRR to change memory ranges.

LoadFailed = ndis2sup.vxd
If the network driver interface specification (NDIS) 2 support driver does not find any NDIS 2 drivers to support, the driver is not loaded.
 

·
Registered
Joined
·
45,855 Posts
The vnbt.386 file is a part of a Netbios protocol. Are you networking and using NetBios as a protocol?

configmg.vxd.....

Hmm, why so long for that? Have you installed the so-called "VXD Fix"? That, I believe, would cause this file to be looked for and loaded differently than it would be otherwise. Normally it is a part of a monolithic (compressed) vmm32.vxd which Windows unpacks each startup. The "fix" takes a number of these files and places them in the vmm32 folder so they don't have to be unpacked each time. But this may actually add some to startup time.
 

·
Registered
Joined
·
157 Posts
Discussion Starter · #7 ·
As far as I know I'm not using netBios, I'm not sure how to tell. Also I haven't applied the vxd fix. This is a clean install of Win 98 just 2 days ago.
Thanks.
 

·
Registered
Joined
·
45,855 Posts
Have a look in the Control Panel's Network applet. If you are not networking all you need is a Dialup adapter, tcp/ip and Windows Logon. You could remove Client for Microsoft Networks and everything else. This might speed things up a little.

Otherwise I don't know what to suggest other than to try another clean install and see if it works out any better.
 

·
Registered
Joined
·
157 Posts
Discussion Starter · #9 ·
Thanks for all your help. Actually I do have a network card, I recently signed up for cable internet service. I found that disabling the nic resulted in a somewhat more "normal" start up time. I guess maybe this is the nature of the beast? I know that all of the computers where I work are networked and have a very long start up time. Since I'm now surfing about 10x faster than before, I guess I can live with it.
 
1 - 10 of 10 Posts
Status
Not open for further replies.
Top