Tech Support Guy banner
Status
Not open for further replies.
1 - 8 of 8 Posts

· Registered
Joined
·
2,507 Posts
Discussion Starter · #1 ·
Hmm.... recent rebuild on my rig meant taking out the old raid system (2 satas) and putting in 2 SSds. In the confusion that always seems to come with it, I dont think I took the RAID off the originals. One of them went back in, shows in BIOS and disk management, but refuses to format. It currently says (through my computer) it sees it, and about 880 0f 931 Gb is used, however opening the drive shows it empty.

All raid is/was through the mobo, the original through Marvell raid, with the disk currently installed on the normal Intel raid set (2 are available onboard), but NOT as part of a raid system.

Tried view hidden files, and most of the normal stuff, formatting normally and through disk management, and every time I get a "cannot format" message.

The info on the disk is not necessary, everything is securely backed up several times. I would like to get the disk working again. any ideas? Thanks

specs as quoted.
 

· Banned
Joined
·
6,440 Posts
The drive probably still has the partition information from the old raid setup.
When you right click in computer management,do you have the option to
delete volume or partition?
If so,delete it,then right click again and create a new volume.
Then format.
If you don't have that option,you might want to wipe the drive and start fresh.
Dban will wipe it for you.
Just make sure you choose the right drive when running this as it will wipe
everything on the drive including partitions.
http://www.dban.org/
 

· Registered
Joined
·
2,507 Posts
Discussion Starter · #4 ·
Sorry.. havent had time to look at this for a couple days.

leroy.. yup, I assumed the raid info was still there. right clicking brings up greyed options, so no luck there. I get shrink volume, but if I try it the volume size stays the same and refuses to shrink anyway. That and format are the only options, and neither work.

Will try your and crj's, see if I can get somewhere.
Thanks guys.. I get this sucker in the end :)
 

· Registered
Joined
·
2,507 Posts
Discussion Starter · #5 ·
Looks like the problem has been resolved, albeit with some unwanted side effects. I managed to get the drive up and running with Paragon
Partition Manager (forgot I even had it, and hadn't installed since the last big format) got it going in the end. Unfortunately this corrupted the MBR ( I have a feeling the drive I was fixing became the system disk) and could not get it back, even with command prompt. Got round it by installing win on the new drive, then using EasyBCD to recognise my original install. Long winded and hassle, but I did want XP 32 to run some old stuff, so all in all, success.
I have the drive back, second OS installed nicely, and old one back. Call it a solved, even though its not quite what I was looking for :)

CRJ- yup, the drives were raided. Speed increase is impossible- sequential write comes out around 350-400 Mb/s. Nice booting :)
 

· Super Moderator
Joined
·
46,767 Posts
One thing to remember is TRIM does not work with raid. You will need to image the array then break the array and secure erase both drives every 6 months or so. Recreate the array and restore the image. Without TRIM, you do not get wear leveling ie the drive are going to wear out faster.
 

· Registered
Joined
·
2,507 Posts
Discussion Starter · #7 ·
Thanks crj- I was aware of the non TRIM within RAID, but hadn't considered a split and recreate. thanks for the info :)
 

· Super Moderator
Joined
·
46,767 Posts
Yes, you will need to do that about every 3~6 months or so to keep the ssds "Fresh"

You can probably do the whole thing in <30min.
 
1 - 8 of 8 Posts
Status
Not open for further replies.
Top