Tech Support Guy banner
Status
Not open for further replies.
1 - 5 of 5 Posts

·
Registered
Joined
·
42 Posts
Discussion Starter · #1 ·
When i boot it shows my ram as 667, and its 800.

My motherboard=

General Information :
Manufacturer : Gigabyte Technology Co., Ltd. (Gigabyte)
Product : GA-MA770-DS3
Version : x.x
Serial Number : Unspecified
Support MP : Yes, 4 CPU(s)
Version MPS : 1.4

Chassis Information :
Manufacturer : Unspecified
Type : Desktop
Version : Unspecified
Serial Number : Unspecified
Asset : Unspecified

Sensor Information :
Hardware Monitoring : ITE IT8718F

On-Board Device Information :
Embedded Controller : No

Slots Information :
Slot PCI : Available (32-bit) 5.0v, 3.3v
Slot PCI : Available (32-bit) 5.0v, 3.3v
Slot PCI-Express : (x16) 3.3v

External Connectors :
Serial 16450 Compatible : DB-9 male
Serial 16450 Compatible : DB-9 male
Parallel ECP/EPP : DB25 female
Keyboard : PS/2
Mouse : PS/2
USB : Access Bus (USB)
USB : Access Bus (USB)
USB : Access Bus (USB)
USB : Access Bus (USB)
USB : Access Bus (USB)
USB : Access Bus (USB)
USB : Access Bus (USB)
USB : Access Bus (USB)
USB : Access Bus (USB)
USB : Access Bus (USB)

Internal Connectors :
PRIMARY IDE : On Board IDE
FDD : On Board Floppy
COM1 : 9 Pin Dual Inline (pin 10 cut)
COM2 : 9 Pin Dual Inline (pin 10 cut)
LPT1 : DB25 female
Keyboard :
PS/2 Mouse : PS/2
USB :
USB :
USB :
USB :
USB :
USB :
USB :
USB :
USB :
USB :

My RAM is

General Information :
A0 (RAS 1) : 1024 (Double Bank)
A1 (RAS 2) : 1024 (Double Bank)
A2 : Empty
A3 : Empty

Information SPD EEPROM (A0) :
Manufacturer : Kingston
Part Number : 9905316-026.A01LF
Serial Number : 9A0483DB
Type : DDR2-SDRAM PC2-5300 (333 MHz) - [DDR2-666]
Format : Regular UDIMM (133.35 x 3)
Size : 1024 MB (2 ranks, 4 banks)
Module Buffered : No
Module Registered : No
Module SLi Ready (EPP) : No
Width : 64-bit
Error Correction Capability : No
Max. Burst Length : 8
Refresh : Reduced (.5x)7.8 µs, Self Refresh
Voltage : SSTL 1.8v
Prefetch Buffer : 4-bit
Manufacture : Week 1 of 2008
Supported Frequencies : 200 MHz, 266 MHz, 333 MHz
CAS Latency (tCL) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @333 MHz
RAS to CAS (tRCD) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @333 MHz
RAS Precharge (tRP) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @333 MHz
Cycle Time (tRAS) : 9 clocks @200 MHz, 12 clocks @266 MHz, 15 clocks @333 MHz
Min TRC : 12 clocks @200 MHz, 16 clocks @266 MHz, 20 clocks @333 MHz

Information SPD EEPROM (A1) :
Manufacturer : Kingston
Part Number : 9905316-026.A01LF
Serial Number : 990483DB
Type : DDR2-SDRAM PC2-5300 (333 MHz) - [DDR2-666]
Format : Regular UDIMM (133.35 x 3)
Size : 1024 MB (2 ranks, 4 banks)
Module Buffered : No
Module Registered : No
Module SLi Ready (EPP) : No
Width : 64-bit
Error Correction Capability : No
Max. Burst Length : 8
Refresh : Reduced (.5x)7.8 µs, Self Refresh
Voltage : SSTL 1.8v
Prefetch Buffer : 4-bit
Manufacture : Week 1 of 2008
Supported Frequencies : 200 MHz, 266 MHz, 333 MHz
CAS Latency (tCL) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @333 MHz
RAS to CAS (tRCD) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @333 MHz
RAS Precharge (tRP) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @333 MHz
Cycle Time (tRAS) : 9 clocks @200 MHz, 12 clocks @266 MHz, 15 clocks @333 MHz
Min TRC : 12 clocks @200 MHz, 16 clocks @266 MHz, 20 clocks @333 MHz

Memory Controller Information :
Memory Controller : Standard, EDO
Number of connectors : 4
Max. Module Size : 1024 MB
Max. Memory Size : 4096 MB
Supported Speed : 70ns, 60ns
Supported Voltages : 3.3v
Error Detection Method : 64-bit ECC
Error Correction Capability : None
Current/Supported Interleave : 1-way/1-way

Can someone please tell me how to get my ram to run at 800Mhz instead of 667Mhz?
 

·
Registered
Joined
·
2,487 Posts
Well, mobo supports up to 1066, according to Gigabyte, so 800 should work. I guess check the mem and make sure it is definitely 800, by looking at it and seeing what it says on the stick iteslf. It sounds like it may be a lower spec from th ereport.
Failing that, check in BIOS that defaults are on for memory, and there are no multipliers hanging around.
 

·
Registered
Joined
·
51,987 Posts
It's possible that 800 is not one of the multiples that you are able to obtain. The speed needs to be a multiple of your bus speed.
 
1 - 5 of 5 Posts
Status
Not open for further replies.
Top