Tech Support Guy banner
Status
Not open for further replies.
1 - 10 of 10 Posts

·
Registered
Joined
·
11 Posts
Discussion Starter · #1 ·
Hello, I'm trying to setup a network between my laptop and desktop computer with a linksys 10/100 network hub.
Both the computers have windows xp pro.

After i run the network setup wizard on both computers,
the desktop seems to have installed fine and can browse and view the workgroup computer mshome. But on my laptop when i try to view the workgroup computers it times out and says...

"mshome is not accessible. You might not have permission to use this network resource.Contact the administrator of the server to find out if you have permissions.the list of servers is currently unavailable"

I also disabled the icf, to make sure that wasn't it.But nothing.

any ideas would be appriecieated.
Thanks

Jeremy
 

·
Registered
Joined
·
8,974 Posts
Did you use the Home Networking Wizard to set it up? As it configures TCP/IP settings, workgroup membership, and Internet Explorer settings for every system on the network, all at once. It is also used to share printers, and create a shared document folder that is accessible to all users from any machine on the network. Also does both PC have the same user accounts? Otherwise you have to enable the Guess account, which is risky.
 

·
Registered
Joined
·
11 Posts
Discussion Starter · #3 ·
yes i ran the setup a small home network wizard on both computers. I have a cable modem and a 5 node hub plus a server running on one of the computers.

The only way i got the network to work was select "this computer connects directly to the internet" from the setup wizard. And then the server stops because its the network changes the ip address, sets it to find ip address automatically, when it needs to be a dynamic ip address , which i need for the server to run.

is there a way to get my laptop to connect to the dynamic ip address and network that way?
 

·
Registered
Joined
·
8,974 Posts
To me "sets it to find ip address automatically" and "dynamic ip address" are the same thing.

I think Windows XP is confused about your setup and you need to manually tweak it.

I think if I understand your setup that the LinkSys hub is acting as a router, firewall, and DHCP host.

Therefore, each PC should be configurated with "this computer connects directly to the internet". You don't want Windows XP being the DHCP host and playing other IP games.

To view computers on your network, click My Network Places on your desktop and then click View Network Computers.

Click View Network Connections and configured the communications correctly.
 

·
Registered
Joined
·
11 Posts
Discussion Starter · #5 ·
ok , yes i understand what your saying about the hub.

What i meant was that i have one staic ip, for the server, and a dynmic for the laptop.

Is there a way that i can network my laptop, with my desktop that has the staic ip?

Becuase when i run the home network setup, it swithches the staic ip on the desktop to "find ip address automatically".

Which means the server wouldn't work after this because it changes the staic ip address.

Thanks again

Jeremy
 

·
Registered
Joined
·
8,974 Posts
Don't re-run the Home Network Setup Wizard. Its job is to go out to every PC and re-configurate it. Like I stated you must now manually tweak the network setting as you have a hy hyper set network. You can use a static address for the server but it must be in the same subnet as the workstations, which are using DHCP from the hub.

i.e., 192.168.100.xxx.

Then My Network Place within My Computer each PC should see each other. Then make your shares and check the user accounts.

For example, on the server and on every PC with shares there is a user account for the PC wishing to use the Share resource.
 

·
Registered
Joined
·
11 Posts
Discussion Starter · #7 ·
ok but how can your use the same settings on both computers ?

When i go to change the subnet on the laptop it requires me to change the ip address also..which on the laptop is static so it sets the ip address automatically right ?
or this wasn't what you were saying?
the exemple you gave looks like an ip address... the subnet i have looks like 255.255.255.0
 

·
Registered
Joined
·
8,974 Posts
The last 3 digits must be different. If you network is configurated as I suggested the LinkSys is the DHCP device. It determines the subnet used. Usually you can configurate the LinkSys a range to use (the low numbers) and save the higher numbers for static IP addresses, such as for servers. If you want to take a chance and not mess with the LinkSys just use a high number for the server, such as .200. As usually it starts with the lower range. To determine what Subnet address you should use for the server check a workstation IP address using My Network Place or by running IPCONFIG.
 

·
Registered
Joined
·
11 Posts
Discussion Starter · #9 ·
I don't know exactly but my isp gave me a subnet mask when i signed up for the static ip address. Its 255.255.255.0 .



I don't understand exactly what your saying but i've come to the conclusion that i should just setup both the computers to use the same subnet mask, but how do i do that without using the same ip address on both machines ? I know i go into network connections and then into the ethernet adapter, and then tcp/ip and set the configurations from there right ?
 
1 - 10 of 10 Posts
Status
Not open for further replies.
Top