Tech Support Guy banner
Status
Not open for further replies.
1 - 9 of 9 Posts

·
Registered
Joined
·
4 Posts
Discussion Starter · #1 ·
I've trawled through the forums here and found similar problems but nothing thats quite the same, or that has the answers which I think I need! I'm very PC literate although a bit foggy sometimes when it comes to hardware...

THE PROBLEM -
My system generally runs without a problem but in the past month or so it's developed a lock-up. The freeze only occurs whilst I am running a game, although it has occurred once whilst using a level editing program.
The picture freezes and the sound enters a repetitive loop, mouse and keyboard are unresponsive and the only way to break free is to manually restart the pc by holding the power switch for 5 seconds... However this problem doesn't occur with all games, the main culprits are WH40K: Dawn Of War and C&C Generals. My specification as you can see below should easily run both games, AND has done perfectly in the past.

I have checked all of the obvious drivers are up to date and re-installed them, plus I have tried both original and updated versions of the games but this hasn't helped...

I did however notice something very odd, im detecting 2 CPUs and I only have ONE installed... Also under the device manager > Computer is 'Multiprocessor PC'..... My pc only has ONE processor, how on earth do I change that and could it be part of the problem?

SPECS -
OS: Windows Xp Pro - Service Pack 2
BIOS: Phoenix - AwardBIOS v6.00PG
CPU: Intel Pentium 4 3.00GHz (2 CPUs) <--- I only have ONE CPU is this normal to be detected like this???
Mother Board: FOXCONN 865A01
Memory: 512MB DDR RAM
HDD: 120Gb (WDC WD1200JB-00DUA0) And 13Gb (SAMSUNG SV1363D)
***I use the 13Gb as a master and is my system disk EVERYTHING else goes onto the larger drive which running as a slave***
DirectX: DirectX 9.0c
3D CARD: RADEON 9600 AGP 256MB DDR
SOUND: EITHER on-board audio Realtek AC97 Audio OR (When that is disabled) Creative Soundblaster Live!Platinum

If you need to know anything else or have any answers or possibilities please, please post. Thanx, Marc...
 

·
Premium Member
Joined
·
52,926 Posts

·
Registered
Joined
·
62 Posts
You gotta admit, if you didn't know about hyperthreading, you'd freak to at the sight of TWO processors when you only have one. lol. That is hilarious.

But yes, what he said is right. lol.
 

·
Registered
Joined
·
4 Posts
Discussion Starter · #4 ·
Triple6 said:
How are you temps?

Download Everest and look under Computer -> Sensor
It should list and identify what the sensors are reading and also list some voltages. See what then temps are at idle and under load.
I've run the program and found the following results

IDLE STATUS.........................................
Sensor Properties:
Sensor Type Winbond W83627HF (ISA 290h)

Temperatures:
Motherboard 35 °C (95 °F)
CPU 41 °C (106 °F)
Aux 49 °C (120 °F)

Cooling Fans:
CPU 2557 RPM
Chassis 2220 RPM

Voltage Values:
CPU Core 1.31 V
CPU Aux 1.46 V
+3.3 V 3.38 V
+5 V 4.97 V
+12 V 11.73 V
-12 V -11.62 V
-5 V -4.60 V
+5 V Standby 5.02 V
VBAT Battery 3.22 V
Debug Info V 52 5B D3 B9 C1 28 3E 23 (01)
Debug Info T 35 41 49

UNDER LOAD.....................................
Sensor Properties:
Sensor Type Winbond W83627HF (ISA 290h)

Temperatures:
Motherboard 38 °C (100 °F)
CPU 59 °C (135 °F)
Aux 49 °C (120 °F)

Cooling Fans:
CPU 2557 RPM
Chassis 2192 RPM

Voltage Values:
CPU Core 1.31 V
CPU Aux 1.44 V
+3.3 V 3.38 V
+5 V 5.00 V
+12 V 11.61 V
-12 V -11.71 V
-5 V -4.65 V
+5 V Standby 4.99 V
VBAT Battery 3.22 V
Debug Info V 52 5A D3 BA BF 27 3D 26 (01)
Debug Info T 38 57 49

After checking out my CPU's design specs this all seems fairly normal and within acceptable limits... I did find that there was a saftey feature in the bios which would force the CPU into an idle state if it reached a certain temp, it was called 'Thermal Throttling' and it was set to 50%. Im not 100% sure how it works, but after reading the manual it stated that the higher the value the lower the temperature was to force and idle state... I have lowered this to 25% (The lowest value available)

Any idea's? I will post again when I've had time to test the system fully for a reasonable amount of time, and decide if this has fixed the problem...
Please reply asap

Thanx alot for reading alla this and for your earlier posts, I really appreciate it! Marc
 

·
Registered
Joined
·
4 Posts
Discussion Starter · #6 ·
Urm im not quite sure how to tell what brand and/or model number I have installed because there are none visable and I don't know a way of getting that info electronicly... I wouldn't imagine its anything particularly special however because I bought the motherboard, RAM and CPU as a package from Novatech (http://www.novatech.co.uk/novatech/home.html) However I've had a quick look through thier current bundled MoBo's (I can't see my exact model there) and all of them are supplied with thier own brand Heatsink and fan.

Just a quick thought, could this problem still be somthingto do with software and or drivers? Afterall the problems only really started after i re-installed xp-pro and added the service packs... I had never had the service packs before so could there possibly be a confliction there? I have since downloaded and updated all of my drivers to be the most recent and up-to-date...

Thanx again for your help so far! Marc
 

·
Registered
Joined
·
823 Posts
mine was doing exactly the same thing but it's an amd . turned out it had a problem with the new nvidia driver for my ti4200 card. rolled back the driver all is well.
also had a problem with service pack 2 so uninstalled it.
 

·
Registered
Joined
·
4 Posts
Discussion Starter · #8 ·
Ahhh ha! Okay well Im away from home atm so I'll get onto trying that when I get back in a few days!
Simple lesson to be learnt from this... don't trust Microsoft for SH*T!!! :D

If anyone else can think of any other possibilities please get in touch, thanx again everyone, the light is at the end of the tunnel!!! Marc
 
1 - 9 of 9 Posts
Status
Not open for further replies.
Top