Tech Support Guy banner
Status
Not open for further replies.
1 - 6 of 6 Posts

·
Registered
Joined
·
3 Posts
Discussion Starter · #1 ·
My wireless was working fine... didn't touch anything and then it stopped.

My roommate can connect fine and I can connect with the ethernet cable.

I ran the Xirrus and it's not detecting any networks and i'm right next to the modem.

I did a system restore, ran a virus scan and no dice.

Any suggestions?
 

·
Super Moderator
Joined
·
65,526 Posts
My roommate can connect fine
your room mate can see the wireless signal and connect ok - is that what you mean ?
Is the wireless switched OFF on the machine
Whats the make and exact model of the PC

can we see a screen shot of device manager , Services and also try a tcp/ip repair

------------------------------------------------------------------------
{Device Manager}
Post back the results in device manager
If you cannot access the internet with this PC, then you will need to copy the program across to the faulty PC
Start > control Panel {Vista set to classic view}> system > {Vista, device manager on left hand side} {XP hardware Tab, device manager button} >
windows 7
start > control panel> System and Security> Device Manager

network adaptors, click on the + > post back the devices listed there
are there any ! ? or X

post a screen shot of the device manager - network adapters

To post a screen shot of the active window, hold the Alt key and press the PrtScn key. Open the Windows PAINT application and Paste the screen shot. You can then use PAINT to trim to suit, and save it as a JPG format file.
To upload it to the forum, open the full reply window and use the Manage Attachments button to upload it here

TCP/IP stack repair options for use with Vista/Windows 7.

Start, Programs\Accessories and right click on Command Prompt, select "Run as Administrator" to open a command prompt.

Note: Type only the text in bold for the following commands.

Reset WINSOCK entries to installation defaults: netsh winsock reset catalog

Reset IPv4 TCP/IP stack to installation defaults. netsh int ipv4 reset reset.log

Reset IPv6 TCP/IP stack to installation defaults. netsh int ipv6 reset reset.log

Reboot the machine.

If you receive the message
The requested operation requires elevation.
The please open the command prompt as administrator - as requested above
Start, Programs\Accessories and right click on Command Prompt, select "Run as Administrator" to open a command prompt.

Post back the results here
rightclick in the box
select all
enter
control key + C key - to copy
then reply here and
control key + V to paste

------------------------------------------------------------------------

------------------------------------------------------------------------
{Services}
post back the status - started/stopped and automatic/manual
Check your Services are Started on all PCs:
  • COM+ Event System (for WZC issues)
  • Computer Browser
  • DHCP Client
  • DNS Client
  • Network Connections
  • Network Location Awareness
  • Remote Procedure Call (RPC)
  • Server
  • TCP/IP Netbios helper
  • Wireless Zero Configuration (XP wireless configurations only)
  • WLAN AutoConfig (Vista wireless configurations only)
  • Workstation

Note: You can check the services in Control Panel, Administrative Tools, Services.

All of these services should be started, and their startup type should be automatic (or perhaps manual).

If a service is not running, open it's properties and check the dependencies. Check each of the dependencies and see which one is preventing the service from running.

Checking the event log is also a good idea here, there may be clues to what is failing.
Start > control panel > administrative tools > event Viewer

------------------------------------------------------------------------
 

·
Registered
Joined
·
607 Posts
Your IPconfig state under your wireless card "media disconnected"
I would assum by this that your wireless is turned off.

Some machines are different to others, but mostly there will either be an actual button on your laptop (normally along the top op the keyboard under the screen) to turn wireles on and off.
Other laptops use the function key by holding FN and then pressing F2. This also turns wireless on and off. Have you looked at or tried either of these?
 

·
Registered
Joined
·
3 Posts
Discussion Starter · #5 ·
I may have run the IPconfig when i had my wireless turned manually off... oops. it's def NOT working when I have it turned on either.

here is the shot of my device manager... i have to run out the door so i can't do the rest just yet.
 

Attachments

·
Super Moderator
Joined
·
65,526 Posts
In addition to the info requested and another ipconfig /all with the wireless switched on
also
make and model of PC
you need some drivers
 
1 - 6 of 6 Posts
Status
Not open for further replies.
Top